Practica 5

Tabla de Direccionamiento

Código Configuración

S1

Switch>ena
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#hostname S1
S1(config)#vlan 5
S1(config-vlan)#name Administracion
S1(config-vlan)#vlan 10
S1(config-vlan)#name Inalambrica
S1(config-vlan)#Vlan 11
S1(config-vlan)#name Personal
S1(config-vlan)#Vlan 18
S1(config-vlan)#name Estudiantes
S1(config-vlan)#int range f0/1-5
S1(config-if-range)#switchport mode trunk
S1(config-if-range)#switchport trunk native vlan 5
S1(config-if-range)#switchport trunk allowed vlan 5,10,11,18
S1(config-if-range)#int vlan 5
S1(config-if)#
%LINK-5-CHANGED: Interface Vlan5, changed state to up

S1(config-if)#ip address 5.5.5.1 255.255.255.0
S1(config-if)#exit
S1(config)#

S3

Switch>ena
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#hostname S3
S3(config)#vlan 5
S3(config-vlan)#name Administracion
S3(config-vlan)#vlan 10
S3(config-vlan)#name Inalambrica
S3(config-vlan)#Vlan 11
S3(config-vlan)#name Personal
S3(config-vlan)#Vlan 18
S3(config-vlan)#name Estudiantes
S3(config-vlan)#int range f0/1-4
S3(config-if-range)#switchport mode trunk
S3(config-if-range)#switchport trunk native vlan 5
S3(config-if-range)#switchport trunk allowed vlan 5,10,11,18
S3(config-if-range)#int vlan 5
S3(config-if)#
%LINK-5-CHANGED: Interface Vlan5, changed state to up
S3(config-if)#ip address 5.5.5.3 255.255.255.0
S3(config-if)#int f0/7
S3(config-if)#switchport mode access
S3(config-if)#switchport mode access
S3(config-if)#switchport access vlan 10

S2

Switch>ena
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#hostname S2
S2(config)#vlan 5
S2(config-vlan)#name Administracion
S2(config-vlan)#vlan 10
S2(config-vlan)#name Inalambrica
S2(config-vlan)#Vlan 11
S2(config-vlan)#name Personal
S2(config-vlan)#Vlan 18
S2(config-vlan)#name Estudiantes
S2(config-vlan)#int range f0/1-4
S2(config-if-range)#switchport mode trunk
S2(config-if-range)#switchport trunk native vlan 5
S2(config-if-range)#switchport trunk allowed vlan 5,10,11,18
S2(config-if-range)#
S2(config-if-range)#int vlan 5
S2(config-if)#
%LINK-5-CHANGED: Interface Vlan5, changed state to up
S2(config-if)#ip address 5.5.5.2 255.255.255.0
S2(config-if)#exit
S2(config)#int f0/11
S2(config-if)#switchport mode access
S2(config-if)#switchport access vlan 11
S2(config-if)#int f0/18
S2(config-if)#switchport mode access
S2(config-if)#switchport access vlan 18
S2(config)#int f0/7
S2(config-if)#switchport mode access
S2(config-if)#switchport access vlan 10

R1

Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname R1
R1(config)#int g0/0
R1(config-if)#no ip address
R1(config-if)#no shut
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
R1(config-if)#int g0/0.5
%LINK-5-CHANGED: Interface GigabitEthernet0/0.5, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.5, changed state to up
R1(config-subif)#encapsulation dot1q 5
R1(config-subif)#ip address 5.5.5.10 255.255.255.0
R1(config-subif)#int g0/0.10
%LINK-5-CHANGED: Interface GigabitEthernet0/0.10, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol o Interface GigabitEthernet0/0.10, changed state to up
R1(config-subif)#encapsulation dot1q 10
R1(config-subif)#ip address 192.168.10.1 255.255.255.0
R1(config-subif)#int g0/0.11
%LINK-5-CHANGED: Interface GigabitEthernet0/0.11, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.11, changed state to up
R1(config-subif)#encapsulation dot1q 11
R1(config-subif)#ip address 11.11.11.1 255.255.255.0
R1(config-subif)#int g0/0.18
%LINK-5-CHANGED: Interface GigabitEthernet0/0.18, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.18, changed state to up
R1(config-subif)#encapsulation dot1q 18
R1(config-subif)#ip address 18.18.18.1 255.255.255.0
R1(config-subif)#int lo 0
%LINK-5-CHANGED: Interface Loopback0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up
R1(config-if)#ip address 10.1.1.1 255.255.255.252
R1(config)#Ip route 192.168.20.0 255.255.255.0 192.168.10.2
R1(config)#Ip route 192.168.30.0 255.255.255.0 192.168.10.3

Archivo